This floor stand holds 1 bike by the crank arm in your garage, home, or office. Stinger inserts into hollow spindle to hold bike's rear wheel above ground for easy washing and light maintenance. Lightweight and easy to take apart for storage.
Specs:
Features:
This lightweight steel floor stand, dubbed the Scorpion, is a convenient bike storage option for your home or at a race or other bike event. The stand holds 1 bike by the crank arm, and it includes adapters for most hollow spindle sizes. It keeps your rear wheel elevated so you can easily wash or perform light maintenance on your bike. It breaks down into 2 pieces for enhanced portability and easy storage.
Easy to Mount Your Bike
To mount your bike to the Scorpion, insert the stinger through the hollow spindle of you bike's crank arm. This holds the bike upright with the rear wheel elevated to allow for continuous spinning. The rack includes 3 cylinder crank spacers (13 mm, 18 mm, and 20 mm in diameter) to adapt to the size of the crank arm's hollow spindle. The convenient push-button sleeve lock secures the spacer onto the stinger. The stand must be used with a spacer to prevent the push-button from being caught inside your bike's crankset. The Scorpion will hold a single mountain bike, downhill bike, road bike, BMX bike, or cross bike that weighs 50 lbs or less.
Convenient Transport and Storage
The lightweight steel rack breaks down into 2 pieces for easy transport. Simply use the included Allen wrench to remove the bolt that holds the stand together. You can then lay the pieces flat for compact storage.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
What's up, everybody It's AJ with etrailer.com. Today, we're gonna be checking out this Feedback Sports Scorpion Bike Stand. It's gonna allow you if you have a hollow crank on your bike, you can load it up here and hold it off itself. Let's check it out. It's gonna be a nice way to keep your bike upright and save some space as well. So instead of leaning against the wall of your garage or moving it all around, it has a stand that you could also do some light maintenance on.
You see the back tire is up off the ground here and allows us to turn the pedals, so we can adjust the chain, we can work on the gear shifting, we can do quite a lot actually with this and not have to worry about holding up the bike while you're working on it. The stand's gonna be in two pieces, so you see it connected right here, so only one bolt holds it together, so that means when you take it apart, it's gonna take up less space too. Now, easy to put together, all you do is find the hollow part of your crank. So I'll slide off here a little bit and show you. This part is what's gonna go into the hollow shank of your bike, so then we're gonna have three different bushings for axle diameters, so you have 13, 18, and 20, so you get three of these.
Make sure you match up with the hollow part of your crank. So we lift up the bike, just the backside, line up. Put one foot on the stand to hold in place as you put it on like that. So I like that there's plenty of the stinger here in the crank, so it's not just on the edge of it, you see I can move it back and forth and not worry that it's gonna fall down. The stand's gonna made out of lightweight steel, so really easy to carry or move around, if you wanna put it in your garage or indoors, not gonna be a problem.
Now, you also have a weight capacity of 50 pounds, so just keep that in mind of what kind of bikes you wanna use with this setup. The stinger itself is gonna be 5 1/2 inches long, it's also gonna work with wheel diameters of 26, 27 1/2, and 29 inches diameter. Comes with the Allen wrench to loosen or tighten up that bolt, so I'm gonna take it apart and show you how much space it takes up when you remove this bolt. Just bring that all the way out and separate it to pieces, and see it pulls down really nice like that. So even when not in use, it's not gonna take up much space.
Something people have commented on is they would've liked rubber grips here at the bottom. You can also get a rubber pad just to have something set it on, giving us more grip and protecting the bottom of the stand. I think that about does it. Thanks for hanging out, and hope this helped.
Average Customer Rating: 4.9 out of 5 stars (7 Customer Reviews)
This floor stand holds 1 bike by the crank arm in your garage, home, or office. Stinger inserts into hollow spindle to hold bike's rear wheel above ground for easy washing and light maintenance. Lightweight and easy to take apart for storage.Yes the scorpion bike stand arrive and did the assembly . Now I’m using it . It’s a good product ! Fantastic!
You know something works well when you don't have to think about. Its been one year since I bought this stand, I use it every day and I am completely satisfied with it.
Great product, easy to put together and perfect for storing your bike or standing it securely so you can work on the back half, clean it, etc. I also appreciate etrailer.com's prompt delivery and amazing customer service. Great job etrailer Team!
I love it. It fits my 1990 Daihatsu Rocky. I bought it so I could get a bike rack in my Rocky at it does that perfectly.
Easy to assemble, Very good quality. I really like how easy it is to use, and how it holds up the bike so well.
Stable and perfect for light repairs and maintenance!
You guys absolutely ROCK!! Got it this morning before we left!!! You guys are really amazing. Kudos!!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.